Custom Printed Temporary Fence Banners: Approve the Fit Before the Artwork
Approve two things before ordering printed fence banners: a drawing that shows how the finished fabric fits the frame and a print sample that shows the artwork on the specified fabric.

Why Fabric Needs a Different Tolerance Strategy
Tolerances for steel fence components are a matter of millimetres and can be held by fixtures.
The strategy described here sorts the dimensions of a screen into functional and cosmetic, sets tolerances for each that reflect how fabric behaves, and ranks inspection so that effort goes where a defect has consequences.
How Much Fabric Dimensions Move
Knitted fabric extends by several per cent under the hand tension used to fit it, and recovers only partly. A dimension measured with the fabric lying slack on a table differs from the same dimension measured under tension.
Creep and shrinkage. Under sustained tension in warm weather the fabric creeps and the screen becomes slack; some fabrics also shrink slightly in their first weeks outdoors. Neither is a manufacturing defect, but both must be allowed for in the nominal size.
Functional Dimensions
A functional dimension is one that decides whether the screen fits the panel and carries its load. There are four.
| Dimension | Function |
|---|---|
| Finished width | Screen spans between frame tubes without overlap onto couplers |
| Finished height | Covers the mesh field; leaves bottom edge free-draining |
| Eyelet spacing | Sets load per tie; eyelets must fall on the frame, not in mid-mesh |
| Eyelet edge distance and hem width | Pull-out strength of eyelet from hem |
Cosmetic Dimensions and Attributes
Cosmetic characteristics affect appearance but not fit or strength. They matter to the client, particularly on branded screens, but they should not be given tolerances as tight as functional ones, and a cosmetic deviation should not be confused with a structural one.
Inspection Priority
| Class | Meaning |
|---|---|
| Critical | Non-conformance creates a safety or compliance risk |
| Major | Non-conformance prevents correct installation or reduces strength |
| Minor | Non-conformance affects appearance only |
Samples
Fabric swatch: at least A4 size, from current production, labelled with mass per unit area and cover factor.
Finished corner sample: showing hem, reinforcement and at least two eyelets, for a hand pull test.
Printed sample: where branding is required, a printed section in the actual colours for approval in daylight.
Writing the Tolerances into the Order
- State the measuring condition for every linear dimension: flat, unstretched, temperature range.
- Give nominal sizes for the screen, not the panel, with the fitting allowance already deducted, and state the panel size it is intended for.
- Specify eyelets by number and position, with corner eyelets dimensioned from both edges, so that the count is unambiguous.
- Approve a reference sample for colour, print and general workmanship, and keep it protected from light.
- Separate functional from cosmetic requirements in two tables, with the classification and acceptance limit for each.
- Agree the response to non-conformance: rejection for critical and major characteristics; concession or price adjustment may be appropriate for minor ones.
- A tolerance scheme of this kind is short, fits on a single drawing sheet, and prevents the two commonest disputes over screens: rejection of serviceable product for small variations in appearance, and acceptance of screens that look right but cannot be fitted tightly.
Fixings and Tie Load
Requirements for fixings should therefore state the tie type and material, its breaking load, UV resistance, the eyelet spacing, and that every eyelet is to be tied.
Receiving Inspection
On delivery, check a sample of screens from each batch: measure width and height, count and measure eyelet spacing, weigh one screen and compare with the stated mass per unit area, pull one eyelet by hand, and compare colour with the approved sample.
Approve the graphic on a mounted sample
A flat print proof can look correct while a join or reinforced hem lands over text once mounted. Tape the supplied artwork outline to the sample or use a full-width proof. Agree a safe area for critical wording and check it in daylight at the intended viewing distance.
Frequently asked questions
Which size should go on a printed fence banner order?
Specify the finished size after hemming and mark any bleed on the artwork separately. Check the usable area against posts, clamps and attachment points.
When should I approve the printed banner proof?
First confirm the panel fit and the approved screened configuration. Review a proof showing folds, joins and eyelets with the artwork positioned as installed.
Related product and planning information
Printed screens & barrier covers · Privacy screens
Further reading · WorkSafe Victoria, Construction site security fencing
Further reading
Browse articles
What to Include in a Temporary Construction Fencing Quote
Ask suppliers to quote the same marked-up perimeter, including gates, bases, clamps, bracing and any screening. A panel-only price leaves the biggest differences in scope unanswered.

Welded Mesh vs. Chain-Link Temporary Fence Panels
Choose the infill around the job and the fleet. Welded mesh gives the panel a rigid grid, while woven chain-link fabric flexes and relies on its ties and frame for support.

How to Buy Front-of-Stage Barriers for Standing Events
Specify a tested front-of-stage barrier assembly for positions exposed to audience pressure. Compare the proposed layout, ground conditions and joining details with the manufacturer's documented rating.
Google Search
Choose KINGCATS as a preferred source
Find our site in Google's source settings and confirm your choice. Availability is determined by Google.
Set preferred source
