Buying Replacement Temporary Fence Feet and Bases
Test replacement fence feet with the panels and clamps already in service. Socket fit, base mass and footprint determine whether the replacement works in the approved fence arrangement.

Five Interface Dimensions
| Dimension | What it must match |
|---|---|
| Socket inside diameter | Outside diameter of the panel leg, plus working clearance |
| Socket depth | Length of panel leg below the bottom rail |
| Socket centre distance | Gap required between adjacent panel frames for the coupler |
| Base height under the panel | Ground clearance of the bottom rail |
| Footprint length and width | Space available; tipping arm a |
Base Types in Use
| Property | Concrete block | Concrete-filled polymer shell | Solid recycled-polymer block |
|---|---|---|---|
| Socket | Cast-in steel or polymer sleeve, or formed hole | Moulded socket in the shell | Moulded or drilled socket |
| Edge and corner damage | Chips and cracks when dropped | Shell protects the concrete; shell can split | Tough; deforms without shattering |
| Handling | Heaviest; hand-holds essential | Moulded hand-holds | Lightest for its size; easy to carry |
Mass, Footprint and Stability
Replacing a base changes two terms in the stability calculation: the base mass mb and the tipping arm a, which is half the footprint length across the fence line.
Weak Interfaces in Mixed Fleets
Polymer socket wear: steel legs enlarge moulded sockets over time. Measure sockets on used bases, not only on new samples, and set a discard limit.
Stacking mismatch: bases that do not nest with the existing type cannot share stillages, and mixed stacks are unstable in transport.
Colour and visibility: bases on footpaths should be clearly visible. If the fleet relies on a high-visibility colour, new bases should match it.
Test Loads
The base is loaded through a test leg, a length of steel tube of the same diameter as the panel leg, inserted in the socket.
Deflection: Reading the Curve
A moment-rotation curve has three parts. At first the leg rotates freely through the socket clearance at almost no moment.
Lean under service load is as important as strength, because a line that leans visibly is treated as unsafe and loosens its couplers.
Impact Tests
Two kinds of impact are relevant. The base itself is dropped, to represent handling. And the assembled panel is struck, to represent a person or object hitting the fence, which loads the socket through the leg at a high rate.
| Test | Observation |
|---|---|
| Drop on a face | Cracks; pieces detached; socket still accepts the leg |
| Cold drop (polymer bases) | Brittle fracture |
| Impact on assembled panel | Panel remains standing or within the permitted displacement; bases and sockets undamaged |
Acceptance Checks Before Ordering
- Coupling: two panels in two bases accept the fleet's standard coupler without forcing, in a straight line and at the tightest curve normally used.
- Mass: weigh the sample; compare with the base it replaces and update the stability schedule.
- Handling and stacking: check hand-holds, stack height and stability on the fleet's stillages.
- Records: note the base type, mass, socket dimensions and the panels it is approved for, so that the compatibility decision can be repeated at the next purchase.
Report
The report identifies the base type, material and production lot, and for recycled polymer the material batch; gives mass and socket dimensions of each specimen; describes the fixture with a sketch or photograph, including the surface, restraint, leg diameter and load height; states the loading rates, hold times, number of cycles, conditioning temperature and drop heights; presents the moment-rotation curves and tabulated rotations at service and proof moment; records all damage with photographs; and states the criteria applied and the result for each specimen. Because recycled-polymer material varies between batches, a short form of the programme, static service load and a cold drop, should be repeated on each material batch.
The Compatibility Problem
The parts usually fit together, in the sense that the tube goes into the socket. A loose socket, a different socket spacing or a lighter base creates a weak interface that shows up later as a leaning line, couplers that will not close, or panels that blow over at a lower wind speed than expected.
Treat a lighter base as a configuration change
A new socket can fit the old panel and still change how the fence bears on the ground. Put the sample mass, footprint and drawing beside the existing specification. Ask the installer or temporary-works designer to approve the substitution for each affected run before ordering the full lot.
Frequently asked questions
What measurements are needed to order a replacement fence foot?
Record the post dimensions, socket depth and shape, clearance and base footprint. Give the supplier the existing part reference or a dimensioned photo.
Is the weight of a replacement base enough to establish compatibility?
Check fit, footprint, ground contact and the base's role in the approved system. Confirm the substitution against the installed configuration.
Related product and planning information
Fence feet & bases · Welded mesh panels
Further reading
Browse articles
Replacing Temporary Fence Privacy Screens: What to Inspect First
Check the fasteners, eyelets and hems before ordering replacement fabric. Damage at several adjacent points, repeated tears or movement of the fence merits a review of the complete screened line.

What to Include in a Temporary Construction Fencing Quote
Ask suppliers to quote the same marked-up perimeter, including gates, bases, clamps, bracing and any screening. A panel-only price leaves the biggest differences in scope unanswered.

Welded Mesh vs. Chain-Link Temporary Fence Panels
Choose the infill around the job and the fleet. Welded mesh gives the panel a rigid grid, while woven chain-link fabric flexes and relies on its ties and frame for support.
Google Search
Choose KINGCATS as a preferred source
Find our site in Google's source settings and confirm your choice. Availability is determined by Google.
Set preferred source
