Industry insights

How to Prepare an Event Barrier Schedule for Stage and FOH

Start with the event layout and mark the front-of-stage line, front-of-house (FOH) enclosure, queues and circulation routes separately. Each zone needs a barrier suited to its role, with quantities and inspection responsibilities on the same schedule.

The Gate in a Crowd Barrier

Barrier lines around stages and front-of-house (FOH) positions must be continuous to resist crowd pressure, and they must also contain openings: for stewards and medics to enter the pit, for people lifted out of the crowd to be led away, for crew to reach the mixing position, and for the audience to leave in an emergency. A gate in such a line has two duties that pull against each other. Closed, it must be as strong and stable as the barrier on either side. Open, it must clear quickly and completely. Achieving both is partly a matter of hardware and largely a matter of coordination between the parties who design, supply, build, operate and approve the event.

Step One: Identify the Zones

ZonePosition
Front-of-stage pit lineBetween audience and stage
Thrust or B-stage edgeAlong runways and satellite stages inside the audience
FOH mix positionSound and lighting control island in the audience
Accessible viewing platformRaised or reserved area
Camera, cable and service runsLanes through or beside the audience

Gate Locations and Functions

GateLocationFunction
Pit entry gateEnd of the front-of-stage barrier, at the side of the stageAccess for stewards, medics and photographers; route for people lifted over the barrier to leave the pit
FOH island gateIn the barrier round the mixing positionCrew access; cable route
Perimeter emergency exitArena fence lineEgress of the audience
Accessible platform gateViewing platform enclosureAccess and egress for platform users

Interfaces

A gate sits at the boundary between several organisations' work. The commonest failures are at those boundaries: the barrier supplier installs a gate where the drawing shows it, the production team runs a cable ramp through it, the security contractor does not staff it, and the licensing officer was shown a different plan.

InterfaceIssue
Barrier system and gateGate section compatible and rated with the barrier; connectors as tested
Gate and groundLevel threshold; firm surface over the swing; trackway joints
Gate and cablesCable ramps and looms crossing the opening
Gate and stewardingWho opens it, on whose instruction
Gate and emergency servicesAccess for vehicles and crews

Responsibility Matrix

  • Decide number, position and width of gates
  • Adopt design crowd load and guidance
  • Supply rated gate sections and evidence of rating
  • Prepare ground at gate positions
  • Keep cables and equipment out of openings
  • Inspect and accept gates before doors
  • Staff gates and operate them during the event
  • Inspect daily and after any incident
  • Record defects and corrective action

Checks Before the Order Is Placed

Quantities: lengths are measured along the barrier line on the drawing, with corner and flex units counted separately, plus spares for damage.

Responsibility: the schedule names who adopted the design load, who verified the product rating and who inspects the installed line before doors open.

Checks Before Doors Open

Each gate is where the approved plan shows it, of the stated width, and opens in the stated direction.

Gate sections are of the barrier system, connected with the specified connectors, and their tread plates are down.

Openings and routes beyond them are clear; no cable ramps, cases or vehicles.

Stewards are in position, briefed and in radio contact; each knows the instruction on which the gate is opened.

The inspection is recorded and signed by the barrier supervisor and the safety adviser, and any change after that time is re-inspected.

From Event Plan to Purchase Specification

A purchase order for barriers around a stage is often written as a length and a product name.

Gate Stability Under Crowd Load

Rated gate sections: gates in a rated line are purpose-made sections of the same barrier system, tested with it.

Make late changes visible in the order

If the sound desk moves, update the drawing, the barrier quantities and the clear routes in a single revision. Ask the supplier to acknowledge the revision against the load assumptions and module schedule. Give the installation supervisor the same revision used for the purchase.

Give every barrier run a reference on the plan

Use one row for each line with a different function or set of conditions. Record the drawing reference, length, required module types, access points and evidence expected with the offer. Where the event plan identifies audience pressure, the specification should name who confirms the load and verifies the proposed system before ordering.

Frequently asked questions

Should the stage and front-of-house barriers be one line on the order?

List them separately so the quote identifies each function, approved barrier type, layout revision and set of components.

What parts are easy to miss in an event barrier schedule?

Check end treatments, corners, changes of barrier type and gate sections against the plan. Assign each part to the run where it will be installed.

Related product and planning information
Events, concerts & festivals · Aluminium stage barriers

Further reading · HSE, Stage barriers and Using barriers at events

Share this article