Industry insights

Temporary Fence Gates for Events: Pedestrian and Vehicle Access

List each opening by the people or vehicles that use it, how often it opens and the clear width it has to provide. A gate's quoted frame size can differ from the usable opening.

Gates as the Working Part of the Fence Line

Staff, vehicles, performers, emergency services and, in an evacuation, the audience itself all pass through openings in a temporary perimeter. A mobile access gate is a panel or pair of panels that hinges, rolls or lifts out of the line and can be relocated with the fence.

It combines the clear width, the number of operating cycles, the wind the leaf is exposed to when open and closed, and the consequence if the gate fails to open.

Three Inputs That Set the Duty

Vehicle gates are sized from the widest vehicle plus working clearance on each side, and from the swept path if the vehicle turns as it enters.

  • Hinges
  • Leaf support
  • Posts and stability

Posts and Coupler Torque

The gate posts, or the fence panels that act as posts, are the foundation of the gate.

Couplers are friction joints, and their capacity is proportional to bolt preload, which is set by torque.

ItemCheck
Tightening torqueTorque wrench on every coupler at the gate; mark after tightening
Hinge clamps or hinge couplersTorque; attempt to move by hand
Post plumbSpirit level on two faces
Bracing of postsVisual against the schedule
BasesPush test; visual

Rules That Apply at Every Duty Level

No trip or snag hazards: bases, stays, drop-bolt sockets and thresholds are kept out of the clear opening.

Screens and banners: none on gate leaves unless the wind force has been checked and hold-open devices are fitted.

Hinge Control

Hinges determine how the leaf moves. Three settings matter: the hinge axis must be vertical, the two hinge pins must be in line, and the hinges must be far enough apart to carry the leaf without excessive force.

CheckAcceptance
Hinge axis verticalLeaf stays where it is left at any point of its swing
Hinge pins in lineLeaf swings without binding at any angle
Leaf level when closedTop rail level; gap at latch stile parallel
Hinge retentionPins captive; leaf cannot be lifted off by an intruder

Latch Control

ItemCheck
Latch engagementMeasure; push and pull the leaf at the latch
AlignmentOperate ten times
Drop boltsOperate; measure engagement
Hold-openEngage; push the leaf
Emergency release (exit gates)Operate from inside; check signage
Double leavesOperate in sequence

Ground and Weather at Festivals

After rain and traffic the gate threshold becomes the softest part of the site.

Functional Testing

The completed gate is tested as it will be used.

A rising opening force over the life of the gate is an early sign of a leaning post, a sinking base or a seized hinge, so the value at handover is recorded as a baseline.

TestMethod
Opening forceSpring balance at the latch stile, pulled at right angles to the leaf, to start and to keep the leaf moving
Clear opening widthTape between the open leaf and the latch post at the narrowest point
Stability under operationPush and pull the closed gate at the latch with a firm hand force; swing the leaf against its stop
Emergency releaseOperate under hand pressure on the leaf, as from a crowd

Handover Criteria

Leaf: level, square, free-swinging through its full arc, staying where it is left.

Latch and bolts: engaging fully; lock fitted; hold-open working.

Safety: no trip hazard in the opening; no finger traps; no sharp edges; signage for exits in place.

Information given to the user: how to operate, lock and hold open; the inspection to be made daily; what to do in high wind; whom to call for adjustment.

Record: gate location and type, installer, date, torque used and wrench identity, measurements, test results, and signatures of installer and user.

Test the opening with its real surroundings

A wheel that runs freely at the depot may cross a cable cover or soft verge at the venue. Ask the bidder to show the wheel path on the proposed drawing. At handover, verify the clear width and full travel with the adjacent fencing and ground finishes in place.

Get a gate schedule with the quotation

Ask for a dimensioned drawing for each opening, with clear width in use, leaf arrangement, direction of travel and the hardware included. For a delivery gate, mark the vehicle turning path. For a public exit, ask the event team to confirm the opening and release method in the approved egress plan.

Frequently asked questions

What width should be specified for a temporary event gate?

Specify the usable opening with the gate in its operating position. Measure between the features that actually limit passage, including projecting hardware.

Can one gate serve pedestrians and service vehicles?

Have the event traffic plan determine the arrangement and operating times. Specify a separate pedestrian opening where routes or simultaneous movements require it.

Related product and planning information
Temporary fence gates · Events, concerts & festivals

Further reading · HSE, Using barriers at events and Crowd controls inside the venue

Share this article