Galvanized Temporary Fence Panels: Pre-Galvanized or Hot-Dip After Fabrication?
The word “galvanized” can describe different production routes. Confirm whether zinc was applied to the strip before forming or to the finished assembly, and ask how seams, cut edges and welds are protected.

Two Routes to a Galvanized Frame
Pre-galvanized tube is roll-formed and seam-welded from strip that was galvanized continuously in the coil.
Hot-dip galvanized tube starts as uncoated ("black") structural or general-purpose tube, for example to EN 10219 or ASTM A500. It is galvanized by immersion in molten zinc, either as tube or, more usefully for fence panels, after the complete frame and mesh have been fabricated (ISO 1461 or ASTM A123).
Coating Mass and Thickness
Continuous coatings are specified by mass per unit area, summed over both faces.
These figures apply to undamaged flat surface.
Coverage: Where the Coating Is Missing
| Zone | Risk if unprotected |
|---|---|
| Outside of seam weld | Rust line along the tube within months in wet conditions |
| Inside of seam weld | Internal rust; staining at tube ends and drain points |
| Tube ends | Rust at ends; limited on thin walls |
| Mesh-to-frame welds | Many small rust spots; commonest complaint |
| Frame joint welds | Rust at the most highly stressed points |
| Scuffs from forming and handling | Minor; zinc protects narrow scratches sacrificially |
Appearance
A sound pre-galvanized surface is smooth and bright to light grey, with or without visible spangle depending on the line. Appearance is not a measure of protection, but certain features indicate a problem.
| Feature | Cause |
|---|---|
| Regular or minimised spangle; slight variation in brightness | Normal solidification of zinc |
| Light scuff marks along the tube | Forming rolls |
| Dark or dull line along the seam | Seam re-protection coating |
| Bare spots or pinholes on the strip surface | Poor wetting in the galvanizing line |
| White powdery deposit | Wet-storage stain from damp stacking |
| Flaking or peeling at bends | Excessive alloy layer or poor adhesion |
What "Pre-Galvanized" Means
The coating is therefore thin, uniform and smooth, and it is present on both the outside and the inside of the tube. It is also interrupted. The longitudinal seam weld burns it away on the tube mill, every cut exposes bare steel at the tube end, and every weld made by the panel manufacturer removes it locally.
Frame Strength in Bending
Diameter and wall thickness therefore deserve at least as much attention as steel grade.
What Is Excluded
| Product | Why excluded |
|---|---|
| Sheet and strip galvanized continuously, and tube made from it (pre-galvanized tube) | Coated in continuous lines before forming |
| Wire for welded mesh and chain-link fabric | Coated continuously as wire |
| Tube galvanized in automatic tube plants | Semi-continuous process with its own requirements |
| Threaded fasteners | Thread fit and centrifuging need specific rules |
| Duplex systems (paint or powder over galvanizing) | ISO 1461 covers only the zinc layer; it notes that after-treatments and overcoating are outside its scope |
Inspection Points
| Inspection point | Comment for temporary products |
|---|---|
| Appearance of significant surfaces | Sharp zinc spikes at drainage points must be removed: these products are handled by hand |
| Flux and ash residues; lumps of zinc | Check inside tube ends and sockets |
| Colour and surface variation | Appearance depends on steel composition; agree a sample if appearance matters |
| Coating thickness | Magnetic method; gravimetric method in dispute |
| Vent and drain holes | Check that holes are present, of adequate size, and free of blocking zinc |
| Fit of moving and mating parts | Check hinge pins, clamp bores, sockets and threads after galvanizing |
What the Standard Covers
ISO 1461 specifies the general properties of coatings, and the test methods for them, applied by dipping fabricated iron and steel articles in molten zinc: the process often called batch, general or after-fabrication galvanizing. The article is made first and coated afterwards, so that all surfaces, edges, welds and, with proper venting, internal surfaces receive the coating.
What to Specify and Verify
- Steel designation and standard for the strip or tube, with minimum yield strength. Avoid forming grades without a yield value where frame strength is required.
- Tube dimensions: outside diameter, wall thickness and tolerances, measured on the steel excluding coating.
- Mechanical test certificate for the tube: yield strength, tensile strength and elongation with the gauge length stated.
- Galvanizing route: pre-galvanized with seam and weld repair, or hot-dip galvanized after fabrication, with the coating standard.
Information to Be Agreed
Significant surfaces: which surfaces are essential to appearance or function, by drawing or sample.
After-treatment: whether articles are to be left unpassivated because powder coating or painting will follow.
Inspection arrangements: where and by whom; how lots are defined.
Certificate: a statement of compliance with ISO 1461 for each delivery, with thickness results on request.
Sampling for Thickness
Thickness is checked on a control sample taken at random from each inspection lot. The standard gives the minimum number of articles according to the lot size.
Ask for a like-for-like coating comparison
When one offer says pre-galvanized and another says hot-dip galvanized after welding, request a drawing showing each coating stage and the surfaces covered. Compare tube section and steel grade separately. Record the agreed inspection method and approved repair for cut or welded areas on the order.
Frequently asked questions
How do I tell whether a quoted fence was galvanized before or after welding?
Ask for the process sequence for the wire mesh and the frame, plus the treatment of welds and cut edges. Request the written specification for the completed panel.
Is a zinc thickness figure enough to compare two fence quotes?
Compare the part measured, the test method, the applicable specification and the inspection lot. The same figure can describe different components.
Related product and planning information
Welded mesh panels · Quality control
Further reading · American Galvanizers Association, Batch Hot-Dip Galvanizing vs. Continuous Galvanizing
Further reading
Browse articles
Galvanized Temporary Gates: What to Check on the Finish at Delivery
Agree which areas of a temporary gate will be inspected and how coating thickness and repairs will be documented. Pay particular attention to hinge brackets, latch posts and surfaces that rub during operation.

What to Include in a Temporary Construction Fencing Quote
Ask suppliers to quote the same marked-up perimeter, including gates, bases, clamps, bracing and any screening. A panel-only price leaves the biggest differences in scope unanswered.

Welded Mesh vs. Chain-Link Temporary Fence Panels
Choose the infill around the job and the fleet. Welded mesh gives the panel a rigid grid, while woven chain-link fabric flexes and relies on its ties and frame for support.
Google Search
Choose KINGCATS as a preferred source
Find our site in Google's source settings and confirm your choice. Availability is determined by Google.
Set preferred source
